FlexaBoot
FlexaBoot is an inexpensive, lightweight, and flexible acoustical sound boot for return air grilles that eliminates sound transfer in open plenum ceilings. Save labor and material costs by Installing FlexaBoots in place of traditional shop fabricated sheet metal return boots. Unlike sheet metal return boots, FlexaBoots are acoustically tested, patented and made with 100% UL classified materials for use in plenum spaces. FlexaBoots offer flexibility above ceilings and are easy to offset over, under and around obstacles. Compared to sheet metal boots, FlexaBoots cost approximately 50% less and weigh 9 lbs compared to 47 lbs sheet metal boots. FlexaBoots are available in 10” and 16” round. The 10” round is typically used with 24x12 face return grilles. The 16” round is typically used with 24x24 face return grilles (return grille not included).
nano Induct
The nano Induct™ is a whole home filterless air purifier that uses proprietary AHPCO™ ionization technology resulting in cleaner air and surfaces in homes or offices. AHPCO technology creates a redundant mixture of ions at levels that, while harmless to people, are 99% effective at deactivating aeroallergens, mold, bacteria, viruses, smoke and formaldehyde. Installed in the HVAC system in minutes, the filterless nano Induct remains out of sight while Ions are distributed throughout the home or office, clearing air and surfaces of unwanted contaminants. There are no filters to replace or maintenance to perform for two years. After two years of use the AHPCO cell is easily replaced in just minutes. Side-by-side competitive testing shows the nano Induct has considerably lower failure rates due to on/off cycling.
Sentry Refrigerant Locking Caps
Sentry Refrigerant Locking Caps meet the International Residential Code (IRC) and International Mechanical Code (IMC) requirement that all outdoor access ports on A/C and refrigerant equipment must be tamper resistant. Sentry Locking Caps safeguard against refrigerant theft and inhalant abuse. These locking caps are anodized in industry color codes for easy identification and prevent accidental mixing of refrigerant gases. The red cap is for easy identification of R-410 refrigerant. The green cap is for easy identification of R-22 refrigerant. The silver cap can be used on different types of refrigerants. The Sentry Universal Key fits refrigerant locking caps from all the major manufacturers. It saves time hunting for the right key at the job site. Fill out the form on this page and be 1 of 500 HVAC pros to receive a free Sentry Universal Key.
AC SmartSeal External
AC SmartSeal External™ is an externally installed emergency refrigerant leak stop that is both easy to apply and suitable for any material. The putty-like compound creates a strong seal with no mess and no need for a flame. Specifically designed to be inert to all kinds of lubricants and refrigerant gases, AC SmartSeal External does not react to temperature changes. To use, simply mix with two fingers, apply to the leak and the leak will be permanently sealed. It does not disperse any residue into the system and can be easily removed. SmartSeal External usage can be combined with SmartSeal: the operator can first seal the larger leak from the outside and then complete the sealing process from the inside with SmartSeal. The two products are not only compatible, but also synergic.
Coolfront Mobile Flat Rate
Coolfront Mobile is a flat rate pricing app designed for HVAC, electrical and plumbing professionals. The app allows technicians to quickly answer a customer’s #1 question of “how much is this going to cost?” With customizable flat rate pricing, Coolfront Mobile also includes scheduling, dispatching, mobile work orders, uploading pictures/videos/files to the work order and real-time updates from the field to the office. Since Coolfront is a web-based application, it works on any smartphone, tablet and computer with or without internet connectivity. With Coolfront Mobile, there are no signup fees, no subscription fees, no contracts and no cancellation fees. Coolfront provides unlimited free training and support so technicians can feel comfortable using the app.
CheckEZ Coil Inspection Frame
The CheckEZ Inspection Frame allows for quick and easy inspection of the evaporative coil on most furnace cabinets. The inspection frame is installed in between the furnace and A/C evaporative coil and has an access hole on each of the four sides of the frame. The access holes provides technicians with a quick and easy way to inspect coils as well as take temperature measurements, static pressure readings and carbon monoxide readings. The frame can be powder coated to standard gray for an overall nice appearance and adds just 1-3/4" to the installation height. With annual inspection of the evaporative coil the HVAC technician can make sure the equipment is performing at the best possible efficiency. The patented inspection frames help contractors sell maintenance contracts, properly set up new installs, help make service technicians more efficient and gives homeowners peace of mind.
Venturo VC1000 Van Crane
Lifts 1,000 LBS and Has a 6' Reach
The all-new VC1000 euro-style van crane from Venturo features a horizontally articulated jib boom that reaches deep within the van to lift heavy equipment and materials up to 1,000 lbs. The crane allows for safe and productive material handling without the need for a forklift or a heavy, expensive liftgate. The Venturo VC1000 van crane utilizes a unique dual floor and ceiling mounted telescopic mast that integrates with the van structure itself to ensure maximum structural integrity. The horizontally articulated boom uses roller bearings that allow the operator to guide the load easily in and out of the van. Two hand levers operate cable controlled multi-position rotation locks. These rotation locks enable the operator to lock the crane in various positions. This key feature adds an additional safeguard for the operator as the load is being loaded and unloaded. The VC1000 is currently offered for Ford Transit and Mercedes-Benz Sprinter models.
Virtual Technician App
The Jackson Systems Virtual Technician App offers technical support to HVAC technicians and installers on-site from anywhere in the country within 15 seconds. The Two-way video allows experienced engineers to see exactly what the technician is seeing in the field. The technician can also see what the engineers are doing to fix the issue. This advancement in technology allows Jackson Systems to visually identify the problem and walk your technician through the solution 75% faster than traditional support by replacing telephone calls that are blindly taken over the phone. There is no being placed on hold, no voicemail and no unanswered calls. In 15 seconds, the technician is face-to-face with a Jackson Systems expert! Simply download the Jackson Systems Virtual Technician App for iPhone or Android and you’ve got our technical support engineers in your back pocket. Whether the tech is having issues installing zoning or wiring a Wi-Fi thermostat, help is just a touch of the CONNECT button away. The Virtual Technician App is available for free to all Jackson Systems' customers.
FlexRight Duct Brace
Eliminates Flexible Duct Kinks
FlexRight shapes any flexible duct into a 90° elbow to eliminate kinks and airflow restrictions. Improved airflow helps save energy and increase room comfort in residential and commercial spaces. FlexRight meets or exceeds ASHRAE, SMACNA and ADC standards, is GreenSpec listed and can contribute to achieving LEED points.
Features & Benefits:
- Replaces Sheet Metal Elbows Sizes 4” through 16”
- Improves Room Comfort
- Increases Airflow Efficiency
- Eliminates Flexible Duct Kinks
- Install on New or Retrofit Existing Ducts
- Residential and Commercial Use
- Made from 100% Recycled Materials
- GreenSpec Listed & UL Classified 2043
HVACBizPro
HVACBizPro is a web based HVAC proposal and flat rate software tool that assists HVAC contractors merchandise products for sale in the customer's home. The easy-to-use sales tool eliminates handwritten proposals and gives the customer up to four different options with detailed descriptions and product brochures, all in less than a couple of minutes. HVACBizPRO ensures the customer has all the information needed to make an educated and informed decision on the best option to fit their comfort needs and budget. Along with proposals, HVACBizPro also features a simple block load analyzer to confirm the proper sizing of the system along with dispatch capability that tracks and directs team members in the field. It also does flat rate service, processes service tickets and creates AHRI match-ups.
LoFlo Balometer Capture Hood
The Alnor® LoFlo® Balometer Capture Hood 6200D is the ideal way to measure very low volumetric flow. Confidently and accurately measure supply or return flows from 10 to 500 cfm (17 to 850 m3/h). This light weight instrument is great for residential or light commercial use.
Features & Benefits:
- Includes a 2' x 2' (610 mm x 610 mm) tall hood
- Weighs only 6.5 lbs. (3 kg) with the hood attached
- 34.5 in. (876 mm) height
- Simulated analog display shows air trends and digital readings
- Uses 4 C-size alkaline batteries; minimum 10 hours continuous use
- For small diffusers, the base can be used without a hood
Cool Air Products Tabs
Clean & Purify Evaporator & Condenser CoilsCool Air Products Tabs make cleaning and purifying AC evaporator and condenser coils simple and cost effective. The small, easy to store tablets are composed of a concentrated solution that are added to one gallon of water to create a properly balanced cleaning solutions. Their compact size requires little storage space in the warehouse and vehicle. A single tablet of Tabs is usually enough to tackle most evaporator coil cleaning jobs. Tabs produce no hazardous waste, never expire and can save consumers and building owners thousands of dollars in maintenance and replacement costs. Tabs are available in 3 forms: Evo Tabs for Evaporators (PH levels 0-7.2), Acid Tabs for Condensers (PH levels 0-7.2) and Alkaline Tabs for Condensers (PH Levels 7.2-14). To use, simply dissolve one Tab in a gallon of water then spray the solution onto the surface of the coils. Wait five minutes and rinse (not necessary with Evo Tabs, as they release a pleasant scent into the air after cleaning.)
RIDGID Thermal Imagers
Predict. Prevent. Perform.
RIDGID thermal imagers feature the latest technology, including the best image in their class and an easy-to-use interface, to help you more efficiently predict problems before they happen and prevent costly downtime. And, the ruggedly built tool, backed by the industry’s best warranty, gives you the confidence to take it on any job. For your thermal imaging needs, turn to the trade’s most trusted brand.
- Features & Benefits:Infrared image resolution up to 320 x 240 (640 x 480 with SuperResolution
- SuperResolution technology adds additional detail in saved images
- Integrated digital camera to view true image alongside infrared image
- Intuitive interface and menu to save time on site
- Easy to grip rubberized overmolding for one handed operation
- Create and share detailed reports with the RIDGID Thermal App
- Request a FREE Demo
PowerMate Stair Climbing Hand Truck
Safely Moves HVAC Equipment Up/Down stairs & On/Off Vehicles
The PowerMate® Stair Climbing Hand Truck safely moves air conditioners, furnaces, heat pumps, boilers, water heaters and more up/down stairs, across flat surfaces as well as on/off vehicles and loading docks. PowerMate keeps the load in a safe, well balanced position allowing the operator to feel safe and secure when moving heavy loads. The battery-operated hand truck does 100% of the lifting and is proven to reduce the physical effort to move heavy loads by 87%. Most loads can be moved by one person instead of 2 or 3, saving time, money and the installer's back. This feature also eliminates the need for a helper which lowers labor costs and provides short-term ROI. Damage to the customer's home/business and workers' comp claims are both significantly reduced when moving heavy equipment with the PowerMate Stair Climbing Hand Truck. PowerMate offers free on-site training along with a one year limited warranty. Fill out the form on this page to ENTER TO WIN a PowerMate Stair Climbing Hand Truck for your business!
Boost Juice
HVAC/R Performance Enhancer in a Can or Flexible Install Hose
Boost Juice® , from DiversiTech,is an HVAC/R system performance improvement additive that lowers energy costs by reducing the amperage draw up to 22% on a system when running. It does this by lubricating the components, removing moisture and oxygen, and dissolving particle debris to a molecular level. This debris is captured in the liquid line drier reducing drag and friction for the refrigerant and oil. Customers can expect to see noticeable improvements in system performance typically within 24 to 72 hours (depending on the state of the system – new versus old) with consistent performance. Noise levels will also be reduced once Boost Juice is installed, providing a long-term benefit to the customer. Boost Juice HVAC/R performance enhancer is designed to be used in units up to 6 tons and is available in a kit with a can or four-foot flexible hose with solution included. Boost Juice is available in a vacuum sealed can as well as a flex-hose injection hose.
Flex Inject Sealant and UV Dye
Easily Injected into System - No Tools Required
DiversiTech has expanded its patent pending flexible hose offering with Flex Inject Sealant Total with UV dye (part #995) and Flash Detect Inject UV dye (part #990). The Total has all the great benefits of Flex Inject Sealant Advanced (part #985) providing 3X more sealing power than comparable injection systems without the need for any tools or manifold gauges. Flex Inject Sealant Total is compatible with all oils and refrigerants, is polymer free and now includes UV dye. The Flex Inject Sealant Total fixes leaks up to 300 microns and also exposes stress and hairline cracks before they turn into major issues, limiting the risk of a return service call. The Flash Detect Inject UV dye focuses strictly on finding leaks and potential system shutdown cracks. For both products, no UV glasses are required and DiversiTech recommends its 89DC UV illuminating light for the dye in both products.
Core EZ w/ Slurry Rings
Drill Your Own Lineset Holes Without the Mess
The CORE EZ Saw, from US Saws, along with the K50 slurry rings significantly reduces operator exposure to silica and slurry waste when drilling small diameter holes in concrete. The K50 Slurry rings are designed to mount via suction to most masonry surfaces and collect over spray and slurry during the drilling process. The rings come in variety of sizes and 6 and 10 inch sizes are most popular. A simple wet dry vac is all that is required to make the core drilling process a clean and almost completely dry process. US Saws introduced the CORE EZ in 2016 as a specialized hole drilling machine designed for the Mechanical, Fire Sprinkler, Electrical and demolition trades. If an HVAC any contractor has to sub out more than 10 holes annually they should own this drilling machine to increase capability, drill on their schedule, and put subcontractor money in their own pocket.
Bi-Polar 2400
We provide value to your customers and profit for your business.
The Bi-Polar® 2400 whole home, filterless air purifier is a small unit -- about the size of a mobile phone. HVAC techs can quickly install this device in almost any A/C unit in minutes while on service/maintenance calls. The unit is a straightforward upsell to offer customers interested in an environmentally friendly way to get relief from poor indoor air quality. The Bi-Polar 2400 reduces allergens, mold, bacteria, viruses, odors and VOCs. Its cold plasma technology replaces the contaminants with healthy, breathable air without the use of UV bulbs or ozone. It works by using bi-polar ionization, splitting water vapor into harmless positive and negative ions that are discharged into the air. These ions attach themselves to allergens such as VOCs, fine particulates, smoke, dust, pollen, dander and more. In addition to deactivating contaminants at the cellular level, particles continue to bond to each other until they are heavy enough to drop out of the air and collect in filters.
ESP Zone Panels
Electronic Static Pressure Control Technology Eliminates the Need to Install Bypass Damper
The new iO ESP zone panels are equipped with award-winning electronic static pressure control technology that eliminates the need to install a bypass damper. As the zone dampers open and close, the static pressure sensor continuously monitors the system static pressure. If the static pressure goes above the static pressure setpoint, the panel will open the non-calling zones just enough to relieve the excess pressure and bring the system below the desired setpoint. This eliminates the need for a conventional bypass damper. Panels are available in 2, 3 and 6 zones, are easy to install and come with a 10 year warranty. Fill out the form on this page or call Jackson Systems at 888-652-9663 to receive 10% off iO zoning with the purchase of an ESP Panel. Use promo code 18ESP10SM. Offer ends April 30, 2018.
Yogapipe Lineset Pipe
A More Efficient Way to Install Linesets
Yogapipe is a flexible line set that offers a faster, more efficient way to install air conditioning line-sets when compared to than copper pipe. With up to Up to 200 feet of joint-free line set connection capabilities, the installer can make adjustments to bends without damaging the pipe. Pre-braze the fittings to equipment anywhere, anytime. With only a crimp operation left to do on-site, you can eliminate the need for hot work permits. Yogapipe doesn’t kink or harden like copper, eliminating dented, damaged and oxidized inventory. The pipe is also completely customizable in length so the installer can determine the length required. The flexible pipe can be pulled through walls, ceilings and bulkheads in one continuous length, perfect for those difficult installation applications. Yogapipe is compliant with the International Mechanical Code, International Residential Code, Uniform Mechanical Code, California Mechanical Code, and Florida Mechanical Code. ICC approval PMG-1409.
Rotobrush Air Duct Cleaning
A Highly Profitable Service for HVAC Contractors
Air duct cleaning is a highly profitable and growing service that HVAC contractors can easily add to their business. With Rotobrush as a partner, you have access to tools needed to help improve the poor indoor air in your current and future customer’s homes. According to the EPA, air duct cleaning services can range from $450 to $1,000! By adding air duct cleaning to your list of services, you will stand apart from the competition and will add more value to your replacement quotes, resulting in more sales.
ICOR NU-22B Refrigerant
See How NU-22B Compares to R-22.
ICOR's NU-22B is an ozone safe replacement that closely matches the operating characteristics of R-22 at a lesser cost. No product-specific tools or supplies are needed to use NU-22B. It’s compatible with all standard oils and all standard equipment components and materials used in R-22 systems with no complications or expensive retrofits. NU-22B is in use in thousands of installations throughout the world and is a high-performance choice for both OEM and service replacement uses and can be used safely and responsibly with complete confidence. See how NU-22B compares to R-22 below.
FF 100 Film Tape for Reflective Insulation
A Film Tape Designed Specifically for Seaming and Sealing Reflective Insulation Shurtape's FF 100 All-Weather Film Tape is designed specifically for permanently seaming and sealing reflective insulation to create a permanent and airtight seal that is free of leaks. FF 100 features an aggressive, all-weather adhesive and flexible film backing that allows it to adhere to the bumpy surface of reflective insulation and seal the insulation for the life of the system. The hand-tearable tape easily withstands thermal cycles and delivers high performance in temperatures ranging from -14° F to 176° F, providing full system closure. And, because FF 100 is designed specifically for reflective insulation, it works just as well when the insulation is installed as a radiant barrier inside an attic, crawlspace, side wall or other area inside a homeor building. Fill out the form to request a FREE Role of FF 100 All-Weather Film Tape.
C450RF Easy Zone Control
RF Wireless Design Eliminates the Need to Install Cables Between the Thermostat and Air Grill
ALAN Manufacturing's new C450RF Easy Zone Control System opens and closes the Floor/Wall Air Grill by using radio frequency (RF) communication method. The system is ideal for hard to reach locations (such as under a vanity), for those who experience physical challenges or anyone that would like to be able to easily control air flow from their registers. The wireless design eliminates the need to install cables between the thermostat and the Air Grill, saving installers valuable time on the job site. The C450RF controls the Air Grill motor and is operated by the thermostat that sends commands. The system is composed of a Control board with Radio Frequency Receiver, the RF Pro Thermostat on the wall, Motor assembly, and Power supply adapter. The C450RF Easy Zone Control System is sold direct to HVAC contractors by Alan Manufacturing.
EasySeal Direct Inject-UV
Permanently Seals Small Refrigerant Leaks & UV Dye Locates Larger Refrigerant Leaks
EasySeal® Direct Inject-UV is a new generation of refrigerant leak sealant with an injection method that makes it easy to install. With this new injection system, there is no need to pump down systems with high pressure refrigerants such as R-410A. The sealantreacts with moisture and air that are naturally present at a leak to permanently seal the leak. The UV dye shows where larger leaks are with the use of a UV light. When injected, EasySeal travels with the refrigerant, searching for and sealing the smallest of leaks in condensers, evaporators, copper lines and soldered joints. It reacts with moisture and air that are naturally present at a leak, forming a permanent seal. Technicians can quickly inject EasySeal Direct Inject-UVinto the system and be confident the leak has been located and fixed without worrying about call backs.
A/C Re-New
Revitalizes Older HVAC Systems & Prevents Call-Backs from Sticking TEVs on New Installs
A/C Re-New® revitalizes older HVAC systems and helps prevent call-backs from sticking TEVs on new installations. The lubricant blends with the system's oil and lasts for the life of the equipment's oil charge. A/C Re-New helps the entire system work more efficiently, resulting in better system performance, cleaner systems, reduced stress on start-up, less wear/tear and lower energy costs. The lubricant also decreases friction within the compressor, silencing loud noises and reducing additional wear-and-tear on the system. Whether installing in a new unit or in an older unit, A/C Re-New is a great up-sell item to help boost profits while helping to prolong the life of your customers' HVAC systems. Fill out the form on this page for more info on how to become an authorized A/C Re-New installer.
AC Smart Seal Quick Shot
Quickly Locate and Repair Refrigerant Leaks Without the Need to Pump Down the System
The AC SMARTSEAL Quickshot Easy Inject Kit helps HVAC technicians to quickly locate and repair refrigerant leaks of all types and sizes without the need to pump down the system. AC SMARTSEAL is the first 3-in-1 sealant on the market with UV dye, sealant and Cool Enhancer that helps extend system life. The OEM approved formula is polymer free and is 100% green, non-toxic, non-flammable and safe to the touch. The kit includes a reusable injection hose that allows technicians to inject AC SMARTSEAL into the system while it is running at normal operating pressures, saving time and energy. The concentrated formula is fully compatible with all refrigerants and permanently seals small pinhole leaks as well as larger leaks with the least amount of sealant.
Zone One Kit
Solves Isolated Over-Heating or Over-Cooling Problems in Office Buildings
Zone One is a modulating or two position zone control system that solves isolated over-heating or over-cooling problems* in office buildings. The damper or diffuser can be used to control a single room or multiple rooms by using a number of dampers and diffusers. Simply run two wires to the 24 volt transformer and three wires to the thermostat and the problem is solved. Zone One uses pressure independent dampers or diffusers combined with individual space thermostats to manage occupant comfort based on individual setpoint preferences. When the Zone One thermostat calls for conditioning of the space, the duct sensor in the damper assembly senses warm or cold air in the duct supply. The thermostat then signals the damper to open or close, depending on the heating/cooling needs.
Aeroseal New Construction
Meet Tight Building Dodes by Sealing Ducts in Less Time than Tape or Mastic
Tighter building codes are causing headaches and costly delays for many builders and HVAC contractors using traditional duct sealing methods. The award-winning Aeroseal duct-sealing technology helps to solve that problem by allowing contractors to effectively seal ducts in less time and with fewer man-hours than traditional tape and mastic. Furthermore, the more profitable Aeroseal technology provides a verifiable seal certificate, eliminating guesswork and callbacks.Aeroseal's patented duct sealing process seals duct leaks from the inside out keeping dust, mold and pollutants from being pulled into living areas. It’s faster, more efficient, and 33% more profitable than hand sealing. Aeroseal can reduce duct leakage by up to 90%, reduce energy use by up to 30% and can dramatically improve indoor comfort.
Diversitech Pro-Series Coil
Request a Free Sample
DiversiTech now offers its most popular Pro-Series coil cleaning solutions in aerosol cans. These six NEW fast and easy to use aerosol products provide contractors and dealers a variety of options for indoor, outdoor and multipurpose applications. Multiple formulas available in popular packaging colors such as Blue, Brown, Green, Yellow and Red along with an environmentally friendly Eco-Coil with each product tailored to address your light, heavy and super heavy duty needs. Whether it is brightening, removing condensate “gunk,” degreasing, dirt and grime, oxide deposits and/or deodorizing, the DiversiTech Pro-Series aerosol cans provide the solutions for condensers, evaporators, microchannels or minisplits. The first 500 HVAC professionals to fill out the form on this page will receive a FREE sample in the color/style of your choice.
Pro-Fit Precision Flaring Kit
Produces Tubing Flares in Seconds Without Splits, Blemishes and Burns
The PRO-Fit™ Precision Flaring Tool creates flares in seconds and is ideal for copper and aluminum line sets, mini-split HVAC units and any application requiring a 45° flare. The spinning hex bits form a standard 45° flare, without splits, burrs, blemishes or uneven edges that typically cause flare fitting connection leaks. The bits are the most efficient option for flaring short stubs or existing tubing in cramped spaces. PRO-Fit is available as a kit that includes five bell-shaped, color-coded, size-inscribed flaring bits designed for 1/4", 3/8", 1/2", 5/8" and 3/4" (6, 7.5, 12, 16, 19-mm) tubing. The flaring process requires just seconds to complete using a (minimum 2000 rpm) drill or impact driver. The standard 1/4" Hex Shank fits directly into most power tools without the need for an adapter.
ClogNever
Eco-Friendly Device Prevents Clogging/Flooding in A/C Units
ClogNever™ is an affordable, eco-friendly device that prevents clogging and flooding in A/C units, while allowing for better performance. The patented electronic device regulates a slow time controlled dripping mechanism that sends the exact amount of an environmentally safe liquid formula that keeps fungus away and assures the flow of water clog free. This device works flawlessly on its own, with the help of a lithium battery for up to five years of usage without human intervention. ClogNever gives the homeowner peace of mind and a worry free assurance that their condensate line is free of clogging. ClogNever can be installed on any type of air conditioner unit. It comes with different accessories to give the tech the ability to attach it to the drain pipe in many different applications.
Gobi II
Universal Mini-Split Condensate Pump
The all new Gobi II Externally Mounted Universal Mini-Split Condensate Pump allows installers and wholesalers to stock a single condensate pump. The Gobi II comes with field configurable dip switches so the technician can optimize each individual installation for sound and flow. The Diagnostic LED light ensures correct installation and assists in diagnostics on future service calls while the USB connection allows technicians with access to review pump history. The Gobi II also features a digital water level sensor that won't get stuck or clogged and has a massive flow range allowing its use from 6,000 Btu/H (1.75kW) up to 120,000 Btu/H (35 kW). Its digital water sensor, universal voltage and user configurable flow ensure it is among the strongest, quietest under A/C mounted condensate pump on the market today.
FilterFetch
Generate Residual Income By Selling Replacement Filter - NO NEED TO STOCK ANT FILTERS
FilterFetch is a free service, from Jackson Systems, that allows HVAC contractors to sell filters to their customers without the need to stock any filters. The When an HVAC Contractors signs up with FilterFetch, they receive a unique contractor code that is printed on a sticker and placed on the HVAC unit. To order filters direct from the HVAC contractor, the homeowner visits filterfetch.com, enters the HVAC contractor's unique code and purchases theirfilters. The filters are then shipped direct to the homeowner and the contractor gets a commission.Customers can order filters of all sizes for every size and system and can receive email reminders that include your logo when it is time to change and reorder. FilterFetch creates a steady revenue stream without the hassle of stocking 2,500+ types of easily damaged filters.
iO-UT32 Titan Thermostat
Affordable Touchscreen Thermostat With Your Logo Imprinted For Free
The iO-Titan is a full-featured, universal touchscreen thermostat that is half the cost of comparable thermostats. The iO-Titan can be battery powered or hardwired which makes it ideally suited for use in residential and light commercial applications. The high quality thermostat is programmable up to 7 days and offers demand staging or locked staging for heat pump applications. It also offers separate heating and cooling differentials for every stage and a high controlling temperature of 120° (ideal for exercise and yoga rooms). Initial setup is easier than ever with the additional dip switches to bypass unused features.
LeakSmart
Detects & Stops Water Leaks in 5 Seconds
The LeakSmart System, sold by Jackson Systems, detects water leaks throughout the home or building and immediately shuts off the water before any damage can occur. The water monitoring and leak prevention system gives homeowners complete control protecting priceless investments from devastating water damage that can lead to mold formation. The leakSMART Valve, Hub and App (available for both iOS and Android), as well as the system’s wireless and waterproof leak sensors, all work together to detect a leak, stop the water immediately and then alert homeowners. This detection grants them unlimited control over their home’s main water supply. LeakSMART can be added to any compatible Zigbee® smart home system. Jackson Systems is offering a free training webinar on January 18th. Fill out the form to register for the free webinar.
TAP Wireless Temperature & Pressure Gauge Set
No App Needed to Calculate Superheat & Subcooling
The new REFCO TAP wireless digital pressure and temperature gauge is a user friendly instrument to measure temperature and pressure from the low and high sides of A/C and Refrigeration systems. The unique feature of the REFCO TAP is the large, easy-to-read pressure and temperature display located on the front of the gauge while the temperature clamp comes standard with a digital display that shows the temperature reading right on the clamp. A mobile App (IOS and Android compatible) is available, but not required since the pressure and temperature readings are clearly displayed on the pressure gauge. Reports can be stored on a mobile device and emailed directly to the home office and to the customer. The gauge stores an extensive library of over 50 refrigerant and temperature/pressure chart updates are available via the micro USB connection. REFCO TAP is available in a single or double set of pressure gauge and temperature clamp. The set includes a pressure gauge and a K-Type temperature clamp for diameters 1/4" to 1 5/8".
Core EZ
Drill You Own Lineset Holes Without The Mess
The K50 Slurry rings, along with the CORE EZ Saw from US Saws, reduces operator exposure to silica and slurry waste when drilling small diameter holes in concrete. The K50 Slurry rings are designed to mount via suction to most masonry surfaces and collect over spray and slurry during the drilling process. The rings come in variety of sizes and 6 and 10 inch sizes are most popular. A simple wet dry vac is all that is required to make the core drilling process a clean and almost completely dry process. US Saws introduced the CORE EZ in 2016 as a specialized hole drilling machine designed for the Mechanical, Fire Sprinkler, Electrical and demolition trades. If an HVAC any contractor has to sub out more than 10 holes annually they should own this drilling machine to increase capability, drill on their schedule, and put subcontractor money in their own pocket.
A/C Easy Tee Contractor Pack
Code Compliant Condensate Cleanout System (25% Discount)
The A/C Easy Tee Condensate Line Service Port System gives service technicians quick and easy access to condensate lines. The Professional Service Tools allow the technician to control the direction of force while using a vacuum to pull the contaminates from the primary drain and water hose, compressed gas or a combination of water and compressed gas to push the contaminates from the condensate line. Simply open the cap, insert the tool, direct the force, clear the drain and close the cap. The system allows you to establish a protocol for drain maintenance and will virtually eliminate call-backs saving you time and money. If you have to cut a condensate line, simply put it back together with the Easy Tee and you’ll never have to cut that line again. CLICK HERE to purchase on Amazon and receive 25% off the purchase price of your first case (Exclusively for Smart HVAC Products subscribers until 10/9/18.)
Sensi Touch Wi-Fi Thermostat
Built-In Install Tools Makes Installation Quick and Easy
The Sensi Touch Wi-Fi Thermostat is equipped with built-in install tools that allow the installer or service technician to work more efficiently. Illuminated terminals allow for increased visibility, while the wiring and easy-click terminals eliminate the need for a screwdriver to install. The thermostat features a high-definition, color touchscreen along with a clean design to fit the modern home. The free, easy-to-use, Sensi mobile app keeps comfort at the homeowners’ fingertips and with features like geofencing, remote access and flexible scheduling, the smartphone app keeps homeowners in-the-know and in control of their home temperature. Sensi thermostat will alert homeowners when there’s a critical condition and will let them know if service is needed. Since the Sensi App stores your contact information, your phone number is just a click away. Sensi termostat is compatible with smart home platforms Apple HomeKit, Amazon Alexa and Wink.
BizPal HVAC Recruiting
An innovative Recruiting Program For Smart HVAC Contractors
BizPAL's innovative recruiting program automatically finds and attracts skilled HVAC tradesman and eliminates wasted time reviewing unqualified applicant resumes. The program is customized to pre-qualify and pre-assess each applicant based on the exact wants and needs for your HVAC business. Unlike other job boards, recruiters, or staffing agencies, BizPAL's recruiting program actively finds experienced candidates and delivers a powerful and motivating recruiting message directly to them. No more posting jobs online, sitting around waiting on applicants nor wondering if applicants have the experience you're looking for. BizPAL recruiting instantly delivers qualified applicants in a quick and easy to reference email. The email contains all the information you want to know about the applicant and with just one click you can quickly contact applicants to schedule an interview.
Gen-Eye Micro-Scope
Compact Video Inspection System Up To 100'
The Gen-Eye Micro-Scope is a handheld inspection tool that inspects up 100' of ductwork along with other hard-to-access areas like heat exchangers, evaporator coils, blower motors and condensate pans. The Micro-Scope reel carries up to 100' of micro push rod along with a 3' probe rod with color camera that allows for inspecting hard to reach areas. The Micro-Scope Command Module™ includes a digital zoom, rotatable picture, voice over recording capability and LED brightness control. On-screen status indicators include date and time, SD card capacity, and battery strength. The rechargeable battery drives the unit for up to four hours. It features a bright, easy-to-see 3.5" LCD screen for viewing crisp, clean pictures and videos. The built-in SD card reader, also allows pictures and videos to be shared on a TV or laptop through a USB port. Three adapters are included to improve the viewing angle or to retrieve objects. General Pipe Cleaners is offering a $100 rebate available until March 31.
The Heater Treater
Earn Residual Income Through Maintenance Agreements and Filter Replacements
The Heater Treater® allows HVAC contractors the ability to offer affordable, yet highly effective protection against scaling on every installation. The Heater Treater provides scale protection for all tankless water heaters, tank water heaters, boilers and solar hot water systems. Water treatment helps maintain efficiency and extends the life of water heaters and boilers, but often times is not utilized due to the high cost to the customer. The Heater Treater is installed on the feed water line just prior to the tankless water heater. As the water passes through the filter cartridge, the treatment media in the interior of the filter slowly dissolves into the water supply providing scale protection to the heater. The units are intended to be used with single and multi heater installs up to 150 GPM and can be installed inside or outside. The Heater Treater will also help your business earn residual income through maintenance agreements and filter replacements.
Aeroseal HomeSeal "Connect"
Seals Ductwork from the Inside Allowing for Duct Sealing in Hard-to-Reach Areas
HomeSeal "Connect" residential duct sealing technology safely seals ductwork from the inside, allowing for duct sealing in hard-to-reach areas using as few as one technician. The technology uses a non-toxic aerosol solution of micron-sized particles that are blown into the pressurized ductwork, seeks out leaks and seals them from the inside. Ducts located under floors, under insulation, in walls and ceilings and in tight spaces are no obstacle when sealing with HomeSeal "Connect". The HomeSeal Connect™ boasts the most cutting edge technological advancements in duct sealing. These technical innovations result in tremendous benefits for contractors that exceed all code standards. HomeSeal "Connect" is ideal for both retrofit and new construction applications and is a great way to differentiate your business and recruit and retain top talent.
Cool Front Agreements
Manage Maintenance Customers with Ease
Coolfront Agreements is a program designed for HVAC, electrical, and plumbing professionals to better manage their maintenance agreement customers. The program allows businesses to better manage, track, call and email agreement customers to prevent customers from falling through the cracks. With emails and phone calls that can be customized, you can tailor your messaging to be as specific or vague as you’d like. You can also customize the timing of these messages as well. Coolfront provides unlimited free training and support so technicians can feel comfortable using the program. Fill out the form on this page to schedule a live one-on-one demonstration.
NU-22B (28oz cans)
Specifically Designed for Small Appliances to Replace R-22
ICOR's NU-22B replacement refrigerant is now available in 28oz cans and was specifically designed for the small appliance repair technician that traditionally services window AC systems and dehumidifiers that were originally R-22 based. This R-22 replacement closely mimics the functions of R-22 and thus creates a high-performance option for OEM and service replacement uses. NU-22B was designed to use the standard oils, equipment components and materials that R-22 systems use, thus preventing you from having to invest in expensive retrofits and equipment. The NU-22B 28 oz cans will be sold separately through ICOR's network of wholesale distributors and sold in a kit that includes: 1 protective carrying case, 2 cans of 28 oz. NU-22B, 1 can Access Valve, a Pressure / Temperature Chart, NU-22B System Conversion Guidelines and a Safety Data Sheet.
